Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
We've noticed this article relating to Installing A Bathtub listed below on the internet and felt it made sense to share it with you here.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Installing a bathtub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, and sometimes, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately tough job. If the old bathtub is conveniently obtainable, the job can move speedily; if you have to open up a wall to eliminate the old tub and place the brand-new bath tub, the job is a lot harder. In either case, the task is within a residence handyman's skills, although you will require an assistant to vacate the old tub as well as embeded in the brand-new one. See to it you have certified yourself for the work as well as are comfortable trying it. Rather than working with a contractor to take control of a halfway-completed project, it is far better to take into consideration utilizing one before you start. Possibilities are you may require a specialist plumber to make tube links.
This write-up will help you set up a new bath tub in your bathroom if you have already purchased a new bathtub and also don't need to change the setup of your previous water system pipes.
Your devices and also material list should consist of the following:
Preparing for the Setup
To start with, the supporting structure provided with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps system to avoid strain on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its last setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, activate the faucets to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be rather problematic because of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. Once the supply pipes have been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. Once the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Installing the Tub
Utilizing both wooden boards under its feet, position the tub in the called for position. The wooden boards are practical in evenly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The next goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the bath tub till the spirit level checks out level.
To install faucets, fit the bottom of the furthest versatile faucet adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other tap.
Turn on the water and examine all joints as well as brand-new pipework for leaks and also tighten them if essential. Load the tub as well as also examine the overflow electrical outlet and also the typical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the maker's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has been used at least once as this will settle it right into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making certain that the washing machines are in place in between the faucet and also the sink. Secure the faucet in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type must be attached to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom and also the tiling, bring about issues with dampness as well as possible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked paper or soft rope. Remember to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealant can fracture fairly early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for spending some time to read our posting. Enjoyed our article? Please share it. Let somebody else check it out. I am grateful for your time. Visit us again soon.
We're waiting, call! Report this page